Will a 150 amp service run a 40 amp EV charger?
| Added demand9,600 VA at 125% — a continuous load | 50A |
|---|---|
| Existing load must stay under | 100A |
| Share of the service this takes | 33% |
| Existing service | 150 A |
| What is being addedthe common 9.6 kW home charger on a 50 A circuit | a 40 A level 2 EV charger |
Notes
- Do not let anyone guess your existing load, including this page. NEC 220.87 gives the real method: take the highest demand recorded in the last 12 months from the utility, multiply by 1.25, and that is your existing load. Most utilities will supply the figure on request; where there is not a year of history, a recording ammeter left on the service for 30 days does the same job. That measured number, plus the 50 A above, is the answer.
- 33% of the service goes to this one thing. Whether it fits depends entirely on what the rest of the house already draws. Under 100 A of existing calculated load and it fits; over, and the service has to grow.
- This is a continuous load, so the code counts it at 125%. A 40 A device is counted as 50 A because it runs for three hours or more without stopping, and conductors and breakers heat differently under a load that never lets up. It is not padding — it is the reason a 40 A charger goes on a 50 A circuit.
- Load management can save the upgrade, and it is worth pricing first. An EV charger with a load-management device, or an energy-management system that sheds the charger when the range comes on, is a listed and code-recognised way to add a large load to a service that could not otherwise take it. It is frequently a fraction of the cost of a new service.
- A panel swap and a service upgrade are different jobs. If the panel is full but the service is adequate, a subpanel or a panel with more spaces solves it for far less. If the calculated load exceeds the service, new breakers change nothing — the conductors from the utility, the meter base and the mast all have to grow.
50 amps added, and the honest half of the answer
Adding a 40 amp EV charger puts 50 A onto the service — 33% of a 150 amp panel. Whether it fits depends on what the house already draws, and that is the number every other page on this subject invents.
Measure the existing load instead of guessing it
NEC 220.87 gives the method, and it is easier than the full calculation. Take the highest demand recorded on the service in the last twelve months, multiply by 1.25, and that is your existing load. Most utilities will provide the figure on request. Where there is not a year of history, a recording ammeter on the service for thirty days does the same job.
If that number is under 100 A, this addition fits.
When load management is the cheaper answer
A charger with a listed load-management device, or an energy-management system that sheds it when the range comes on, is a code-recognised way to put a large load on a service that could not otherwise take it. It is often a fraction of the cost of a new service, and it is worth pricing before anyone quotes a mast and a meter base.
A full panel is a different problem
If the breakers have run out but the calculated load is fine, a subpanel or a panel with more spaces solves it cheaply. Only when the load exceeds the service does the utility conductor, meter base and mast all have to grow.
Nearby sizes
Read more
- Service Upgrade vs Panel Upgrade: Two Jobs With the Same NameA new panel does not give a house more power. Only the service conductors, the meter socket and the utility connection decide how many amps come in.
- Meter Base With Disconnect: What It Is and When Code Requires OnePutting the main breaker outside changes what the panel inside is. Whether it becomes a subpanel, with separated neutrals and grounds and a four-wire feeder, depends on which of three options you choose.
- Cost to Upgrade From 100 to 200 Amp Service, Line by LineThe panel is the cheap part. The meter socket, the service conductors, the grounding and whatever the inspector finds behind the old panel decide whether the bill is $2,000 or $5,000.
- Grounding and Bonding — The Part of the Service Nobody SeesThe grounding system does nothing at all until something goes wrong, which is why it is the part most often found inadequate.